RENESAS R9A07G075M24GBG#AC0

MPU is a high-performance application-specific standard product featuring dual Arm Cortex-R52 processors with FPU and NEON. It integrates peripheral functions required for system configuration.

• On-chip 32-bit Arm Cortex-R52 processor
  • High-speed realtime control with operating frequency of 200/400/800 MHz
  • On-chip Dual/Single 32-bit Arm Cortex-R52 (revision r1p2)
  • Tightly coupled memory (TCM) with ECC: CPU0: 512KB/64KB, CPU1: No support
  • Instruction cache/data cache with ECC: CPU0: 16KB per cache, CPU1: 32KB per cache
  • High-speed interrupt
  • The FPU supports addition, subtraction, multiplication, division, multiply-and-accumulate, and square-root operations at single-precision and double-precision.
  • The NEON, Advanced SIMD, supports integer or single precision results.
  • Supports architecture with 8-stage pipeline
  • Arm CoreSight architecture, includes support for debugging through JTAG and SWD interfaces.
  • No DCLS (Dual Core Lock Step) support
• Low power consumption: Standby mode and module stop function
• On-chip SRAM: 2.0 MB/1.5 MB of the on-chip SRAM with ECC, 150/200 MHz
• Data transfer: DMAC: 16 channels × 2 units
• Event link controller: Module operations can be started by event signals rather than by interrupt handlers. Linked operation of modules is available even while the CPU is in the standby state.
• Reset and power supply voltage control: Five reset sources including a pin reset
• Clock functions:
  • External clock/oscillator input frequency: 25 MHz
  • CPU clock frequency: 200/400/800 MHz or 150/300/600 MHz
  • System clock frequency: 200 MHz or 150 MHz
  • Low-speed on-chip oscillator (LOCO): 240 kHz
• Safety functions: Register write protection, input clock oscillation stop detection and CRC, Master Memory Protection Unit (MPU)
• Security functions (optional):
  • Boot mode with security through encryption
  • JTAG authentication
  • Cryptologic accelerator
  • TRNG
• Encoder interfaces (optional):
  • 2 channels
  • EnDat 2.2, BiSS-C, FA-CODER, A-format, and HIPERFACE-DSL-compliant interfaces
  • Frequency-divided output from an encoder
• Various communications interfaces:
  • Ethernet
  • EtherCAT slave Controller: 3 ports
  • Ethernet switch: 3 ports
  • Ethernet MAC: 1 port
  • USB 2.0 high-speed host/functions: 1 channel
  • CAN/CANFD (compliant with ISO11898-1): 2 channels
  • SCI with 16-byte transmission and reception FIFOs: 6 channels
  • I²C bus interface: 3 channel for transfer at up to 400 kbps
  • SPI: 4 channels
• External address space:
  • Buses for high-speed data transfer at up to 100 MHz
  • Support for up to 4 CS areas
  • 8-, 16- or 32-bit bus space is selectable per area
• Up to 35 extended-function timers:
  • 16-bit × 8 + 32 bit MTU3 (9 channels), 32-bit GPT (18 channels): Input capture, output compare, PWM waveform output
  • 16-bit CMT (6 channels), 32-bit CMTW (2 channels)
• ΔΣ interface: Up to 6ΔΣ modulators are connectable externally.
• Trigonometric function unit:
  • Simultaneous calculation of sine and cosine
  • Simultaneous calculation of arctangent and hypot_k
• 12-bit A/D converter: 12 bits × 2 unit (8 channels for unit 0, 16 channels for unit 1)
• Temperature sensor for measuring temperature within the chip
• General-purpose I/O ports:
  • Input pull-up/pull-down
  • The locations of input/output functions for peripheral modules are selectable from among multiple pins.
• Operating temperature range: Tj = -40 to +125°C