MICROCHIP PIC16F1773-E/SO

PIC16(L)F1773/6 microcontrollers feature a high level of integration of intelligent analog and digital peripherals for a wide range of applications, such as lighting, power supplies, battery charging, motor control and other general purpose applications. These devices deliver multiple op amps, 5-/10-bit DACs, high-speed comparators, 10-bit ADC, 10-/16-bit PWMs, programmable ramp generator (PRG) and other peripherals that can be connected internally to create closedloop systems without using pins or the printed circuit board (PCB) area. The 10-/16-bit PWMs, digital signal modulators and tri-state output op amp can be used together to create a LED dimming engine for lighting applications. The peripheral pin select (PPS) functionality provides flexibility, eases PCB layout and peripheral utilization by allowing digital peripheral pin mapping to an I/O.

• C Compiler Optimized RISC Architecture
• Only 49 Instructions
• Operating Speed:
  • DC – 32 MHz clock input
  • 125 ns minimum instruction cycle
• Interrupt Capability
• 16-Level Deep Hardware Stack
• Five 8-Bit Timers
• Three 16-Bit Timers
• Low-Current Power-on Reset (POR)
• Configurable Power-up Timer (PWRT)
• Brown-out Reset (BOR) with Selectable Trip Point
• Extended Watchdog Timer (EWDT):
  • Low-power 31 kHz WDT
  • Software selectable prescaler
  • Software selectable enable
• Up to 28 Kbytes Program Flash Memory (PFM)
• Up to 2 Kbytes Data RAM
• Direct, Indirect and Relative Addressing modes
• High-Endurance Flash (HEF):
  • 128B of nonvolatile data storage
  • 100K Erase/Write cycles
• Operating Voltage Range:
  • 1.8V to 3.6V (PIC16LF1773/6)
  • 2.3V to 5.5V (PIC16F1773/6)
• Temperature Range:
  • Industrial: -40°C to 85°C
  • Extended: -40°C to 125°C
• Sleep mode: 50 nA @1.8V, typical
• Watchdog Timer: 500 nA @ 1.8V, typical
• Secondary Oscillator: 500 nA @ 32 kHz
• Operating Current:
  • 8 uA @ 31 kHz, 1.8V, typical
  • 32 uA/MHz @1.8V, typical
• 10-Bit Analog-to-Digital Converter (ADC):
  • Up to 28 external channels
  • Conversion available during Sleep
• Three Operational Amplifiers (OPA):
  • Selectable internal and external channels
  • Tri-state output
  • Part of LED dimming engine
• Six High-Speed Comparators (HS Comp):
  • Up to nine external inverting inputs
  • Up to 12 external non-inverting inputs
  • Fixed Voltage Reference at inverting and non-inverting input(s)
  • Comparator outputs externally accessible
• Digital-to-Analog Converters (DAC):
  • Three 10-bit resolution DACs 10-bit resolution, rail-to-rail
  • Conversion during Sleep
  • Internal connections to ADCs and HS Comparators
• Voltage Reference:
  • Fixed Voltage Reference (FVR) - 1.024V, 2.048V and 4.096V output levels
• Zero-Cross Detector (ZCD):
  • Detect high-voltage AC signal
• Three Programmable Ramp Generators (PRG):
  • Slope compensation
  • Ramp generation
• High-Current Drive I/Os:
  • Up to 100 mA sink or source @ 5V
• Four Configurable Logic Cells (CLC):
  • Integrated combinational and state logic
• Three Complementary Output Generators (COG):
  • Push-pull, Full-Bridge and Steering modes
• Three Capture/Compare/PWM (CCP) Modules
• Pulse-Width Modulator (PWM):
  • Three 16-bit PWMs
  • Independent timers
  • Multiple output modes (Edge-, CenterAligned, set and toggle on register match)
  • User settings for phase, duty cycle, period, offset and polarity
  • 16-bit timer capability
  • Three 10-bit PWMs
• Digital Signal Modulator (DSM):
  • Modulates a carrier signal with a digital data to create custom carrier synchronized output waveforms
  • Part of LED dimming engine
• Peripheral Pin Select (PPS):
  • I/O remapping of digital peripherals
• Serial Communications:
  • Enhanced USART (EUSART)
  • SPI, I2C, RS-232, RS-485, LIN compatible
  • Auto-Baud Detect, auto-wake-up on start
• Up to 25 I/O Pins:
  • Individually programmable pull-ups
  • Slew rate control
  • Interrupt-on-change with edge-select
• Precision Internal Oscillator:
  • ±1% at calibration
  • Selectable frequency range 32 MHz to 31 kHz
• 31 kHz Low-Power Internal Oscillator
• 4x Phase-Locked Loop (PLL) for up to 32 MHz Internal Operation
• External Oscillator Block with Three External Clock modes up to 32 MHz

• lighting
• power supplies
• battery charging
• motor control
• other general purpose applications