MICROCHIP PIC16LF1613-E/SL

PIC12/16(L)F161X microcontrollers deliver on-chip features that are unique to the design for embedded control of small motors and general purpose applications in 8/14/20-pin count packages. Features like 10-bit A/D, CCP, 24-bit SMT and Zero-Cross Detection offer an excellent solution to the variety of applications. The product family also has a CRC+ memory scan and Windowed WDT to support safety-critical systems in home appliances, white goods and other end equipment.

• C Compiler Optimized RISC Architecture
• Only 49 Instructions
• Operating Speed:
  • DC – 32 MHz clock input
  • 125 ns minimum instruction cycle
• Interrupt Capability
• 16-Level Deep Hardware Stack
• Up to Four 8-bit Timers
• Up to Three 16-bit Timers
• Low Current Power-on Reset (POR)
• Configurable Power-up Timer (PWRT)
• Brown-out Reset (BOR) with Selectable Trip Point
• Window Watchdog Timer (WWDT):
  • Variable prescaler selection
  • Variable window size selection
  • All sources configurable in hardware or software
• Up to 8 KW Flash Program Memory
• Up to 1024 Bytes Data SRAM Memory
• Direct, Indirect and Relative Addressing modes
• High-Endurance Flash Data Memory (HEF):
  • 128 B (nonvolatile), 100K Erase/Write Cycles
• Operating Voltage Range:
  • 1.8V to 3.6V (PIC16LF161X)
  • 2.3V to 5.5V (PIC16F161X)
• Temperature Range:
  • Industrial: -40℃ to 85℃
  • Extended: -40℃ to 125℃
• Sleep mode: 50 nA @1.8V, typical
• Watchdog Timer: 500 nA @ 1.8V, typical
• Secondary Oscillator: 500 nA @ 32 kHz
• Operating Current:
  • 8 uA @ 32 kHz, 1.8V, typical
  • 32 uA/MHz @ 1.8V, typical
• Configurable Logic Cell (CLC):
  • Up to four CLCs
  • Integrated combinational and sequential logic
• Complementary Waveform Generator (CWG):
  • Rising and falling edge dead-band control
  • Full-bridge, half-bridge, 1-channel drive
  • Multiple signal sources
• Two Capture/Compare/PWM (CCP) modules
• PWM: Two 10-bit Pulse-Width Modulators
• Two Signal Measurement Timers (SMT):
  • 24-bit timer/counter with prescaler
  • Multiple gate and clock inputs
• Angular Timer:
  • Single pulse
  • Multiple pulses with missing pulse recovery
• Hardware Limit Timer (HLT):
  • 8-bit timer with prescaler
  • 8-bit period register and postscaler
  • Asynchronous H/W reset sources
• Math Accelerator:
  • Four operation modes
  • Add and multiply
  • Simple multiplier
  • Multiply and Accumulate (MAC)
  • Programmable PID controller
• Cyclic Redundancy Check with Memory Scan (CRC):
  • Software configurable
• Serial Communications:
  • Enhanced USART (EUSART)
  • SPI, I2C, RS-232, RS-485, LIN compatible
  • Auto-Baud Detect, Auto-Wake-up on start
• Up to 18 I/O Pins:
  • Individually programmable pull-ups
  • Slew rate control
  • Interrupt-on-change with edge-select
• Peripheral Pin Select (PPS):
  • Enables pin mapping of digital I/O
• 10-Bit Analog-to-Digital Converter (ADC):
  • Up to 12 external channels
  • Conversion available during Sleep
• Two Comparators (CMP):
  • Low-Power/High-Speed mode
  • Up to three external inverting inputs
  • Fixed Voltage Reference at non-inverting input(s)
  • Comparator outputs externally accessible
• 8-Bit Digital-to-Analog Converter (DAC):
  • 8-bit resolution, rail-to-rail
  • Positive Reference Selection
• Voltage Reference:
  • Fixed Voltage Reference (FVR): 1.024V, 2.048V and 4.096V output levels
• Zero-Cross Detect (ZCD):
  • Detect when AC signal on pin crosses ground
• 16 MHz Internal Oscillator:
  • ±1% at calibration
  • Selectable frequency range from 32 MHz to 31 kHz
• 31 kHz Low-Power Internal Oscillator
• 4x Phase-Locked Loop (PLL):
  • For up to 32 MHz internal operation
• External Oscillator Block with:
  • Three external clock modes up to 32 MHz

• Embedded control for small motors
• General-purpose applications
• Home appliances
• White goods
• Other end equipment
• Safety-critical systems