LCSC Electronics logoLCSC Electronics svg logo
Anmelden
USD
TI TPS61301YFFT product image
Abbildung ähnlich

TI TPS61301YFFT

Hersteller
Herst.-Teilenr.
TPS61301YFFT
LCSC-Nr.
C2879602
Verp.
DSBGA-20
Kundennummer
Hauptmerkm.
1.92MHz PWM 3 DC-DC 5.7V 2.5V~5.5V DSBGA-20 LED Drivers RoHS
DatenblattTI TPS61301YFFT
RoHS-Konformität1 Dokumente verfügbar
Alternativteile5
Garantie auf jede Bestellung
100% Authentisch · 30-Tage-Rückgabe oder -Umtausch
Nicht vorrätig
Benachrichtigen
Minimum: 1Vielfaches: 1Verkaufseinheit: Piece
Zur BOM-Liste hinzufügen
Stk.E-Preis(Nur als Referenz)Gesamtbetrag
1+$ 3.8908$ 3.89
250+$ 1.5062$ 376.55
500+$ 1.4539$ 726.95
1,000+$ 1.427$ 1427.00
Standardgehäuse250/Full Reel
Besserer Preis bei größerer Menge?
$

Produktspezifikationen

Alle
TypBeschreibung
KategorieIntegrated Circuits (ICs)/Power Management (PMIC)/LED Drivers
HerstellerTI
Verp.DSBGA-20
Frequency - Switching1.92MHz
DimmingPWM
Voltage - Input(AC)-
Number of Channels3
TypeDC-DC
Switch tube (built-in/external)Built-in
Output Voltage5.7V
Operating Temperature-40℃~+85℃
Output Current400mA;800mA
FeaturesOver Voltage Protection;Short Circuit Protection;Over-Temperature Protection (OTP)
TopologyBoost
Constant Current Accuracy10%
Voltage - Input(DC)2.5V~5.5V

Beschreibung

KI-Übersetzung

The TPS6130xx device is based on a high-frequency synchronous boost topology with constant current sinks to drive up to three white LEDs in parallel (400‑mA, 800-mA, and 400-mA maximum flash current). The extended high-current mode (HC_SEL) allows up to 1025-mA, 2050-mA, and 1025-mA flash current out of the storage capacitor. The high-capacity storage capacitor on the output of the boost regulator provides the high-peak flash LED current, thereby reducing the peak current demand from the battery to a minimum. The 2-MHz switching frequency allows the use of small and low profile 2.2-μH inductors. To optimize overall efficiency, the device operates with a 400-mV LED feedback voltage. The TPS6130xx device not only operates as a regulated current source, but also as a standard voltage boost regulator. The device keeps the output voltage regulated even when the input voltage exceeds the nominal output voltage. The device enters power-save mode operation at light load currents to maintain high efficiency over the entire load current range. To simplify flashlight synchronization with the camera module, the device offers a trigger pin (FLASH_SYNC) for zero latency LED turnon time.

Merkmale

KI-Übersetzung
  • Four Operational Modes
  • DC Light and Flashlight
  • Voltage Regulated Converter: 3.8 V to 5.7 V
  • Standby: 2 μA (Typical)
  • Storage Capacitor Friendly Solution
  • Automatic VF and ESR Calibration
  • Power-Save Mode for Improved Efficiency at Low Output Power, Up to 95% Efficiency
  • Output Voltage Remains Regulated When Input Voltage Exceeds Nominal Output Voltage
  • I2C Compatible Interface up to 3.4 Mbits/s
  • Zero Latency Tx-Masking Input
  • Hardware Voltage Mode Selection Input (TPS61300, TPS61301)
  • DC Light Mode Selection Input (TPS61300, TPS61306)
  • Hardware Reset Input (TPS61301, TPS61305)
  • LED Temperature Monitoring (TPS61305)
  • Privacy Indicator LED Output
  • Integrated LED Safety Timer
  • Total Solution Size of Less Than 25 mm² (<1 mm height)
  • Available in a 20-Pin NanoFree (DSBGA)

Anwendungen

KI-Übersetzung
  • Single, Dual, or Triple White LED Flashlight Supply for Cell Phones and Smart-Phones
  • LED Based Xenon Killer Flashlight
  • Audio Amplifier Power Supply

Alternativteile

MPNHerstellerAlternativtypVerpackungVerfügbarkeitStückpreis
TPS61305YFFRTIÄhnlicheDSBGA-200$ 3.2423
TPS61300YFFRTIÄhnlicheDSBGA-200$ 1.5585
TPS61305YFFTTIÄhnlicheDSBGA-200$ 3.8908
TPS61300YFFTTIÄhnlicheDSBGA-200$ 3.8908
TPS61301YFFRTIÄhnlicheDSBGA-200$ 3.2423