RENESAS R5F562TAADFM#V3

RX62T Group, RX62G Group Renesas MCUs 100-MHz 32-bit RX MCUs, FPU, 165 DMIPS, 12-bit ADC (3 S/H circuits, double data register, amplifier, comparator): two units, 10-bit ADC one unit, the three ADC units are capable of simultaneous 7-ch. sampling, 100-MHz PWM (two three-phase complementary channels and four single-phase complementary channels or three three-phase complementary channels and one single-phase complementary channel)

• 32-bit RX CPU core
  • Max. operating frequency: 100 MHz, Capable of 165 DMIPS in operation at 100 MHz
  • Single precision 32-bit IEEE-754 floating point
  • Accumulator handles 64-bit results (for a single instruction) from 32-×32-bit operations
  • Multiplication and division unit handles 32-×32-bit operations (multiplication instructions take one CPU clock cycle)
  • Fast interrupt Divider (fastest instruction execution takes two CPU clock cycles)
  • Fast interrupt
  • CISC Harvard architecture with 5-stage pipeline
  • Variable-length instructions: Ultra-compact code
  • Supports the memory protection unit (MPU)
  • Background JTAG debugging plus high-speed tracing
• Operating voltage
  • Single 3.3- or 5-V supply; 5-V analog supply is possible with 3.3-V products
• Low-power design and architecture
  • Four low-power modes
• On-chip main flash memory, no wait states
  • 100-MHz operation, 10-ns read cycle
  • No wait states for reading at full CPU speed
  • 64-Kbyte/128-Kbyte/256-Kbyte capacities
  • For instructions and operands, User code programmable via the SCI or JTAG
• On-chip data flash memory
  • Max. 32 Kbytes, reprogrammable up to 30,000 times
  • Erasing and programming impose no load on the CPU
• On-chip SRAM, no wait states
  • 8-Kbyte/16-Kbyte SRAM, For instructions and operands
• DMA DTC: The single unit is capable of transfer on multiple channels
• Reset and supply management
  • Power-on reset (POR)
  • Low voltage detection (LVD) with voltage settings
• Clock functions
  • External crystal oscillator or internal PLL for operation at 8 to 12.5 MHz
  • Internal 125-kHz LOCO for the IWDT
  • Detection of main oscillator stoppage (for IEC 60730 compliance)
• Independent watchdog timer (for IEC60730 compliance)
  • 125-kHz LOCO clock operation
  • Software is incapable of stopping the robust WDT
• Up to 7 communications interfaces
  • 1: CAN (compliant with ISO11898-1), incorporating 32 mailboxes
  • 3: SCIs, with asynchronous mode (incorporating noise cancellation), clock-synchronous mode, and smart-card interface mode
  • 1: I2C bus interface, capable of SMBus operation
  • 1: RSPI
  • 1: LIN
• Up to 16 16-bit timers
  • 8: 16-bit MTU3: 100-MHz operation, input capture, output compare, two three-phase complementary PWM output channels, complementary PWM imposing no load on the CPU, phase-counting mode
  • 4: 16-bit GPT: 100-MHz operation, input capture, output compare, four complementary single-phase PWM output channels, or one three-phase complementary PWM output channel and one single-phase complementary PWM output channel, complementary PWM imposing no load on the CPU, operation linked with comparator (for counting and control of PWM-signal negation), detection of abnormal oscillation frequencies (for IEC 60730 compliance)
  • 4: 16-bit CMT
• Generation of delays in PWM waveforms (only for the RX62G Group)
  • The timing with which signals on the 16-bit GPT PWM output pin rise and fall can be controlled with an accuracy of up to 312 ps (in operation at 100 MHz)
• Three A/D converter units for 1-MHz operation, for a total of 20 channels
  • Three units are capable of simultaneous sampling on seven channels
  • Self diagnosis (for IEC60730 compliance)
  • 8: Two 12-bit ADC units: three sample-and-hold circuits, double data registers, amplifier, comparator
  • 12: Single 10-bit ADC unit
• CRC (cyclic redundancy check) calculation unit
  • Monitoring of data being transferred (for IEC 60730 compliance)
  • Monitoring of data in memory (for IEC 60730 compliance)
• Up to 61 input–output ports and up to 21 input-only ports
  • PORT registers: Monitoring of output ports (for IEC 60730 compliance)
• Operating temp. range
  • -40℃ to +85℃
  • -40℃ to +105℃