MICROCHIP AT89C5131A-RDTUM

AT89C5131 is a high-performance Flash version of the 80C51 single-chip 8-bit microcontrollers with full speed USB functions. AT89C5131 features a full-speed USB module compatible with the USB specifications Version 1.1 and 2.0. This module integrates the USB transceivers with a 3.3V voltage regulator and the Serial Interface Engine (SIE) with Digital Phase Locked Loop and 48 MHz clock recovery. USB Event detection logic (Reset and Suspend/Resume) and FIFO buffers supporting the mandatory control Endpoint (EP0) and up to 6 versatile Endpoints (EP1/EP2/EP3/EP4/EP5/EP6) with minimum software overhead are also part of the USB module. AT89C5131 retains the features of the Atmel 80C52 with extended Flash capacity (32- Kbyte), 256 bytes of internal RAM, a 4-level interrupt system, two 16-bit timer/counters (T0/T1), a full duplex enhanced UART (EUART) and an on-chip oscillator. In addition, AT89C5131 has an on-chip expanded RAM of 1024 bytes (ERAM), a dualdata pointer, a 16-bit up/down Timer (T2), a Programmable Counter Array (PCA), up to 4 programmable LED current sources, a programmable hardware watchdog and a power-on reset. AT89C5131 has two software-selectable modes of reduced activity for further reduction in power consumption. In the idle mode the CPU is frozen while the timers, the serial ports and the interrupt system are still operating. In the power-down mode the RAM is saved, the peripheral clock is frozen, but the device has full wake-up capability through USB events or external interrupts.

• 80C52X2 Core (6 Clocks per Instruction) – Maximum Core Frequency 48 MHz in X1 Mode, 24MHz in X2 Mode – Dual Data Pointer – Full-duplex Enhanced UART (EUART) – Three 16-bit Timer/Counters: T0, T1 and T2 – 256 Bytes of Scratchpad RAM
• 32-Kbyte On-chip Flash In-System Programming through USB or UART
• 4-Kbyte EEPROM for Boot (3-Kbyte) and Data (1-Kbyte)
• On-chip Expanded RAM (ERAM): 1024 Bytes
• USB 1.1 and 2.0 Full Speed Compliant Module with Interrupt on Transfer Completion – Endpoint 0 for Control Transfers: 32-byte FIFO – 6 Programmable Endpoints with In or Out Directions and with Bulk, Interrupt or Isochronous Transfers – Endpoint 1, 2, 3: 32-byte FIFO – Endpoint 4, 5: 2 x 64-byte FIFO with Double Buffering (Ping-pong Mode) – Endpoint 6: 2 x 512-byte FIFO with Double Buffering (Ping-pong Mode) – Suspend/Resume Interrupts – Power-on Reset and USB Bus Reset – 48 MHz DPLL for Full-speed Bus Operation – USB Bus Disconnection on Microcontroller Request
• 5 Channels Programmable Counter Array (PCA) with 16-bit Counter, High-speed Output, Compare/Capture, PWM and Watchdog Timer Capabilities
• Programmable Hardware Watchdog Timer (One-time Enabled with Reset-out): 50 ms to 6s at 4 MHz
• Keyboard Interrupt Interface on Port P1 (8 Bits)
• TWI (Two Wire Interface) 400Kbit/s
• SPI Interface (Master/Slave Mode)
• 34 I/O Pins
• 4 Direct-drive LED Outputs with Programmable Current Sources: 2-6-10 mA Typical
• 4-level Priority Interrupt System (11 sources)
• Idle and Power-down Modes
• 0 to 32 MHz On-chip Oscillator with Analog PLL for 48 MHz Synthesis
• Low Power Voltage Range – 3.0V to 3.6V – 30 mA Max Operating Current (at 40 MHz) – 100 μA Max Power-down Current
• Industrial Temperature Range
• Packages: PLCC52, VQFP64, MLF48, SO28