MICROCHIP AT91SAM7S64C-AU

Atmel’s SAM7S is a series of low pincount Flash microcontrollers based on the 32-bit ARM RISC processor. It features a high-speed Flash and an SRAM, a large set of peripherals, including a USB 2.0 device (except for the SAM7S32 and SAM7S16), and a complete set of system functions minimizing the number of external components. The device is an ideal migration path for 8-bit microcontroller users looking for additional performance and extended memory. The embedded Flash memory can be programmed in-system via the JTAG-ICE interface or via a parallel interface on a production programmer prior to mounting. Built-in lock bits and a security bit protect the firmware from accidental overwrite and preserves its confidentiality. The SAM7S Series system controller includes a reset controller capable of managing the power-on sequence of the microcontroller and the complete system. Correct device operation can be monitored by a built-in brownout detector and a watch

• Incorporates the ARM7TDMI ARM Thumb Processor
  • High-performance 32-bit RISC Architecture
  • High-density 16-bit Instruction Set
  • Leader in MIPS/Watt
  • EmbeddedICE In-circuit Emulation, Debug Communication Channel Support
  • 512 Kbytes (SAM7S512) Organized in Two Contiguous Banks of 1024 Pages of 256 Bytes (Dual Plane)
  • 256 Kbytes (SAM7S256) Organized in 1024 Pages of 256 Bytes (Single Plane)
  • 128 Kbytes (SAM7S128) Organized in 512 Pages of 256 Bytes (Single Plane)
  • 64 Kbytes (SAM7S64) Organized in 512 Pages of 128 Bytes (Single Plane)
  • 32 Kbytes (SAM7S321/32) Organized in 256 Pages of 128 Bytes (Single Plane)
  • 16 Kbytes (SAM7S161/16) Organized in 256 Pages of 64 Bytes (Single Plane)
  • Single Cycle Access at Up to 30 MHz in Worst Case Conditions
  • Prefetch Buffer Optimizing Thumb Instruction Execution at Maximum Speed
  • Page Programming Time: 6 ms, Including Page Auto-erase, Full Erase Time: 15 ms
  • 10,000 Write Cycles, 10-year Data Retention Capability, Sector Lock Capabilities, Flash Security Bit
  • Fast Flash Programming Interface for High Volume Production
  • 64 Kbytes (SAM7S512/256) – 32 Kbytes (SAM7S128) – 16 Kbytes (SAM7S64) – 8 Kbytes (SAM7S321/32) – 4 Kbytes (SAM7S161/16)
• Advanced Interrupt Controller (AIC)
  • Individually Maskable, Eight-level Priority, Vectored Interrupt Sources
  • Two (SAM7S512/256/128/64/321/161) or One (SAM7S32/16) External Interrupt Source(s) and One Fast Interrupt Source, Spurious Interrupt Protected
• Debug Unit (DBGU)
  • 2-wire UART and Support for Debug Communication Channel interrupt, Programmable ICE Access Prevention
  • Mode for General Purpose 2-wire UART Serial Communication
• Periodic Interval Timer (PIT)
  • 20-bit Programmable Counter plus 12-bit Interval Counter
• Windowed Watchdog (WDT)
  • 12-bit key-protected Programmable Counter
  • Provides Reset or Interrupt Signals to the System
  • Counter May Be Stopped While the Processor is in Debug State or in Idle Mode
• Real-time Timer (RTT)
  • 32-bit Free-running Counter with Alarm
  • Runs Off the Internal RC Oscillator
• One Parallel Input/Output Controller (PIOA)
  • Thirty-two (SAM7S512/256/128/64/321/161) or twenty-one (SAM7S32/16) Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os
  • Input Change Interrupt Capability on Each I/O Line
  • Individually Programmable Open-drain, Pull-up resistor and Synchronous Output
• Eleven (SAM7S512/256/128/64/321/161) or Nine (SAM7S32/16) Peripheral DMA Controller (PDC) Channels
• One USB 2.0 Full Speed (12 Mbits per Second) Device Port (Except for the SAM7S32/16).
  • On-chip Transceiver, 328-byte Configurable Integrated FIFOs
• One Synchronous Serial Controller (SSC)
  • Independent Clock and Frame Sync Signals for Each Receiver and Transmitter
  • I²S Analog Interface Support, Time Division Multiplex Support
  • High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer
• Two (SAM7S512/256/128/64/321/161) or One (SAM7S32/16) Universal Synchronous/Asynchronous Receiver Transmitters (USART)
  • Individual Baud Rate Generator, rDA⊕ Infrared Modulation/Demodulation
  • Support for ISO7816 T0/T1 Smart Card, Hardware Handshaking, RS485 Support
  • Full Modem Line Support on USART1 (SAM7S512/256/128/64/321/161)
• One Master/Slave Serial Peripheral Interface (SPI)
  • 8- to 16-bit Programmable Data Length, Four External Peripheral Chip Selects
• One Three-channel 16-bit Timer/Counter (TC)
  • Three External Clock Input and Two Multi-purpose I/O Pins per Channel (SAM7S512/256/128/64/321/161)
  • One External Clock Input and Two Multi-purpose I/O Pins for the first Two Channels Only (SAM7S32/16)
  • Double PWM Generation, Capture/Waveform Mode, Up/Down Capability
• One Four-channel 16-bit PWM Controller (PWMC)
• One Two-wire Interface (TWI)
  • Master Mode Support Only, All Two-wire Atmel EEPROMs and I²c Compatible Devices Supported (SAM7S512/256/128/64/321/32)
  • Master, Multi-Master and Slave Mode Support, All Two-wire Atmel EEPROMs and I²c Compatible Devices Supported (SAM7S161/16)
• One 8-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os
• SAM-BA Boot Assistant
  • Default Boot program
  • Interface with SAM-BA Graphic User Interface IEEE 1149.1 JTAG Boundary Scan on All Digital Pins
• 5V-tolerant I/Os, including Four High-current Drive I/O lines, Up to 16 mA Each (SAM7S161/16 I/Os No
• Power Supplies
  • Embedded 1.8V Regulator, Drawing up to 100 mA for the Core and External Components
  • 3.3V or 1.8V VDDIO I/O Lines Power Supply, Independent 3.3V VDDFLASH Flash Power Supply
  • 1.8V VDDCORE Core Power Supply with Brown-out Detector
• Fully Static Operation: Up to 55 MHz at 1.65V and 85⋅C Worst Case Conditions
• Available in 64-lead LQFP Green or 64-pad QFN Green Package (SAM7S512/256/128/64/321/161) and 48-lead LQFP Green or 48-pad QFN Green Package (SAM7S32/16)