NXP LPC4333JET100E

The LPC435X_3X_2X_1X are ARM Cortex-M4 based microcontrollers with Floating Point Unit (FPU) for embedded applications which include an ARM Cortex-M0 coprocessor, up to 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, two high-speed USB controllers, Ethernet, LCD, an external memory controller, a quad SPI Flash Interface (SPIFI) that supports execute-in-place, advanced configurable peripherals such as the State Configurable Timer (SCTimer/PWM) and the Serial General Purpose I/O (SGPIO) interface, and multiple digital and analog peripherals. The LPC435X_3X_2X_1X operate at CPU frequencies of up to 204 MHz.

The ARM Cortex-M4 is a 32-bit core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration. The ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals, and includes an internal prefetch unit that supports speculative branching. The ARM Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A hardware floating-point processor is integrated into the core.

The ARM Cortex-M0 coprocessor is an energy-efficient and easy-to-use 32-bit core, which is upward code- and tool-compatible with the Cortex-M4 core. It is ideal for handling control or peripheral handling to free up the Cortex-M4 for real-time processing. The Cortex-M0 coprocessor offers up to 204 MHz performance with a simple instruction set and reduced code size. In LPC43xx, the Cortex-M0 coprocessor hardware multiply is implemented as a 32-cycle iterative multiplier.

• Cortex-M4 Processor core
  • ARM Cortex-M4 processor (version r0p1), running at frequencies of up to 204 MHz.
  • Built-in Memory Protection Unit (MPU) supporting eight regions.
  • Built-in Nested Vectored Interrupt Controller (NVIC).
  • Hardware floating-point unit.
  • Non-maskable Interrupt (NMI) input.
  • JTAG and Serial Wire Debug (SWD), serial trace, eight breakpoints, and four watch points.
  • Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.
  • System tick timer.
• Cortex-M0 Processor core
  • ARM Cortex-M0 co-processor (version r0p0) capable of off-loading the main ARM Cortex-M4 application processor.
  • Running at frequencies of up to 204 MHz.
  • JTAG
  • Built-in NVIC.
• On-chip memory
  • Up to 1 MB on-chip dual bank flash memory with flash accelerator.
  • 16 kB on-chip EEPROM data memory.
  • 136 kB SRAM for code and data use.
  • Multiple SRAM blocks with separate bus access. Two SRAM blocks can be powered down individually.
  • 64 kB ROM containing boot code and on-chip software drivers.
  • 64 bit + 256 bit of One-Time Programmable (OTP) memory for general-purpose use.
• Configurable digital peripherals
  • Serial GPIO (SGPIO) interface.
  • State Configurable Timer (SCTimer/PWM) subsystem on AHB.
  • Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and outputs to event driven peripherals like the timers, SCTimer/PWM, and ADC0/1.
• Serial interfaces
  • Quad SPI Flash Interface (SPIFI) with four lanes and up to 52 MB per second.
  • 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping (IEEE 1588 - 2008 v2).
  • One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY.
  • One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to external high-speed PHY.
  • USB interface electrical test software included in ROM USB stack.
  • One 550 UART with DMA support and full modem interface.
  • Three 550 USARTs with DMA and synchronous mode support and a smart card interface conforming to ISO7816 specification. One USART with IrDA interface.
  • Up to two C_CAN 2.0B controllers with one channel each.
  • Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support.
  • One SPI controller.
  • One Fast-mode Plus I2C -bus interface with monitor mode and with open-drain I/O pins conforming to the full I2C -bus specification. Supports data rates of up to 1 Mbit/s.
  • One standard I2C -bus interface with monitor mode and with standard I/O pins.
  • Two I2S interfaces, each with DMA support and with one input and one output.
• Digital peripherals
  • External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash, and SDRAM devices.
  • LCD controller with DMA support and a programmable display resolution of up to 1024 H×768 V. Supports monochrome and color STN panels and TFT color panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel mapping. Available on parts LPC4357/53 only.
  • Secure Digital Input Output (SD/MMC) card interface.
  • Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB slaves.
  • Up to 164 General-Purpose Input/Output (GPIO) pins with configurable pull-up/pull-down resistors.
  • GPIO registers are located on the AHB for fast access. GPIO ports have DMA support.
  • Up to eight GPIO pins can be selected from all GPIO pins as edge and level sensitive